Description
The 555 is ubiquitous and can be used as simple PWM speed control
Circuit Diagram
Circuit Explaination:
The 555 is ubiquitous and can be used as simple PWM speed control
Circuit Diagram
The 555 Ic is wired as an astable and the frequency is constant and
independent of the duty cycle, as the total resistance (R charge + R
discharge, notice the diode) is constant and equal to 22Kohm (givin a
frequency of about 1Khz, notice the hum).
When the potentiomenter is all up, the Rcharge resistance is 1,0 Kohm
(the diode prevents the capacitor to charge through the second
potentiometer section and the other 1,0 Kohm resistor) , and Rdischarge
is 21 Kohm, giving a 5% on duty cycle and a 1Khz frequency.
When the potentiomenter is all down, the Rcharge resistance is 21,0 Kohm
(the diode prevents the capacitor to charge through the second
potentiometer section and the other 1,0 Kohm resistor) , and Rdischarge
is 1 Kohm, giving a 95% on duty cycle and a 1Khz frequency.
When the potentiomenter is at 50% , the Rcharge resistance is 11,0 Kohm
(the diode prevents the capacitor to charge through the second
potentiometer section and the other 1,0 Kohm resistor) , and Rdischarge
is 11 Kohm, giving a 50% on duty cycle and a 1Khz frequency.
The 555 provide good current capability to drive the mosfet fast and to
drive a bipolar transistor.
I actually use this system to drive the DC motor of my small Rotary
spark gap Tesla coil at variable speed
If you are disgusted by the 1Khz hum of the motor try to rise the
frequency out of the audible range (replacing the potenziometer), but
rembember that at higher frequency inductive reactance of motor rises so
the the efficiency would drop.
Important:
Obviously the mosfet (or bipolar) must have enough current capability to drive the motor, so the drain (or collector) current must be equal to maximum motor current (at power supply voltage, when it is blocked). The snubber diode too, because it shorts the motor on the off cycle. Both mosfet (or bipolar) and diode have to be hooked (if you don't want them cooked ;-) ) to a heatsink if the max motor current is more than 100 or 200mA. I suggest to not stress to much the motor with too much work because it overheats both motor, transistor and diode. If you don't want braking in the off cycle just place a resistor in series with the snubber diode, it should rise a bit efficiency but have more inertia when slowing the motor down. The value of the resistor must be R=V(breakdown transistor) / Imax, and the power should be 5W. Mosfets have internal zener diode, but don't count on it ;-)
Author: Jonathan Filippi, jonathan.filippi@virgilio.it
Source http://www.electronics-lab.com/
Obviously the mosfet (or bipolar) must have enough current capability to drive the motor, so the drain (or collector) current must be equal to maximum motor current (at power supply voltage, when it is blocked). The snubber diode too, because it shorts the motor on the off cycle. Both mosfet (or bipolar) and diode have to be hooked (if you don't want them cooked ;-) ) to a heatsink if the max motor current is more than 100 or 200mA. I suggest to not stress to much the motor with too much work because it overheats both motor, transistor and diode. If you don't want braking in the off cycle just place a resistor in series with the snubber diode, it should rise a bit efficiency but have more inertia when slowing the motor down. The value of the resistor must be R=V(breakdown transistor) / Imax, and the power should be 5W. Mosfets have internal zener diode, but don't count on it ;-)
Author: Jonathan Filippi, jonathan.filippi@virgilio.it
Source http://www.electronics-lab.com/
Post a Comment